Gorman-Rupp S Series Model S3A1 3 in. NPT Ductile Iron Widebase Submersible Dewatering Pump, 230V 1P, 280 GPM

SKU:
GORS3A1230V1P
Manufacturer:
Gorman-Rupp
Size:
3 in.
Flow-Rate:
280 GPM
Product Type:
230V AC
Weight:
160.00 LBS
$8,781.90
Adding to cart… The item has been added

Gorman-Rupp Widebase submersible dewatering pumps tackle the big jobs. Where large solids are not a problem, these versatile models offer high-head, high-volume operation and stand up to the abuses of the worst conditions. Whatever the application - general construction, strip mining, tunnel work or general purpose - Gorman-Rupp Widebase pumps are built to operate quietly, effectively and safely.

Note: Control panel included.

Disclaimer: Please call 1-800-333-3331 for detailed information concerning your model. Parts lists can sometimes vary from pump to pump. Your serial number is critical in determining the correct parts and service requirements for your pump. Information on this page is provided for reference only.

Warning: Do not use in explosive atmosphere or pump volatile flammable liquids.

Features

  • High Head, High Volume Solutions: Gorman-Rupp Wide Base Submersibles are designed for applications where high volume and high head are required, and large solids are not a problem - Pumps have only two moving parts and three wearing surfaces so maintenance and repairs are minimal
  • Abrasive Handling Impeller: Abrasion-resistant ductile iron and manganese bronze impellers stand up to sand, gravel and other abrasive materials - The fully shrouded impeller back reduces seal pressure and helps prevent foreign material from entering the seal cavity - Seal life is extended and operational life of the pump is increased. Optional impellers of CD4mCu are available for corrosive/abrasive applications
  • Dual Seals, Double Protection: Primary seal keeps dirty water in the pump end and prevents contamination of the oil cavity - A second "fail safe" seal provides extra protection against the possibility of damage to the motor - Positive oil lubrication enables the pump to run dry without seal damage
  • Corrosion-Resistant Stainless Hardware: Rotor shaft and all internal nuts and bolts coming in contact with the liquid are made of stainless steel to resist corrosion and pitting and extend the operational life of the pump - For severely corrosive/abrasive applications, stainless steel lifted pump models of CD4MCu are available

Specifications

Pump Specifications:
  • Part: S3A1 230V 1P
  • Series: S Series - Widebase Submersible
  • Model: S3A1
  • Suction: 3 in. (80 mm.)
  • Discharge: 3 in. (80 mm.)
  • Flange: NPT
  • Flow-Rate: 280 GPM
  • Solids Handling: 0.38 in. (10 mm.)
  • Casing: Ductile Iron
  • Impeller/Rotor: Ductile Iron
  • Drive: 230V 1 Phase Electric Motor
  • Seal: Tungsten Carbide
  • Diffuser: Ductile Iron 80-60-03; Maximum Operating Pressure 71 psi (490 kPa)*
  • Impeller: Ductile Iron 60-40-18
  • Suction Head: Ductile Iron 65-45-12
  • Intermediate: Aluminum Alloy 356-T6
  • Motor Housing: Aluminum Alloy 356-T6
  • Motor Shaft: Stainless Steel 416
  • Bearings: Upper, Open Single Row Ball Bearing; Lower, Open Double Row Ball Bearing
  • Discharge Elbow: Aluminum Alloy 356-T6
  • Gaskets: Cork with Nitrile Binder (NC710)
  • O-Rings: Nitrile Rubber
  • Wetted Hardware: Standard Plated Steel and Stainless Steel
  • Strainer: Urethane Coated Steel. 50.6% Open Area, 0.38 in. (9,6 mm) Diameter Openings.
  • Hoisting Bail: Urethane Coated Steel
Standard Equipment:
  • NEMA Type 3R Rainproof Control Box: Provides On-Off, Circuit Breaker and Motor Overload Protection
Optional Equipment:
  • Liquid Level Control
    • Turtle Type Pressure Activated Level Switch
    • Float Activated Level Switch
  • Staging Adapter Kit
Motor/Cable Specifications:
  • Motor: Oil Filled Enclosure; 5.0 H.P.; 3450 R.P.M.
    • Single Phase: 230 Volt, 60 Hz, 28 Full Load AMPS, 5.4 kW (Max.)
    • Three Phase: 200/230/460/575 Volt, 60 Hz, 18/16/8/6.5 Full Load AMPS, 5.3 kW (Max.)
  • Power Cable: 6 Wire; Type GGC; 8 AWG; 3 Power Conductors, 2 Ground and 1 Ground Check. Nominal Length 50 Feet (15 m) Standard (Specify Alternate Length at Time of Order.)
  • Recommended Generator Size: 15 kW Across the Line Start
Seal Specifications:
  • Double, Mechanical, Type 2, Oil Lubricated - Nitrile Rubber and Fluorocarbon Elastomers (DuPont Viton or Equivalent) - Brass Cage and Stainless Steel 18-8 Spring
    • Upper Faces: Carbon Rotating Face, Ni-Resist Stationary Face
    • Lower Faces: Tungsten Titanium Carbide Rotating and Stationary Faces
  • Maximum Temperature of Liquid Pumped 122 F (50 C)*

*Consult Factory for Applications Exceeding Maximum Pressure and/or Temperature Indicated.