110 Gallon Aluminum Rectangle Split Fuel Transfer Tank w/ GPI 8 GPM Pumps (12V DC)

JME 110 Gallon Aluminum Rectangle Split Fuel Transfer Tank Description

The JME 110 Gallon Split Fuel Transfer Tank is a DOT-approved aluminum tank backed by a Special Permit from the U.S. Department of Transportation, ensuring it meets all legal requirements for manufacture, marking, and sale. Built for commercial, state, and private applications, this tank is engineered to withstand tough conditions while providing reliable, long-lasting service. It is certified for Gasoline, Diesel, Methanol, Kerosene, Aviation fuel, and other liquids.

Paired with the tank, the GPI 12V DC EZ-8 Fuel Transfer Pump delivers a gas station-equivalent flow rate of up to 8 GPM using a durable rotary gear design made of corrosion-resistant diecast aluminum. The pump handles gasoline, diesel, ethanol blends, and kerosene, making it ideal for recreational vehicles, agriculture, automotive, or portable fueling needs. Easily mounted to drums or tanks up to 100 gallons, this pump and tank combination provides a portable, high-performance refueling solution.

Attention: Adhere to these guidelines before installation. Failure to follow these guidelines will result in voiding your warranty.

• The fill cap location and pump location cannot be swapped.
• Do not install risers between the fuel tank fitting and the pump.
• Do not use extension pipes to raise the height of the transfer pump.
• Do not install a pump over 30 lbs. to a standard duty tank. For pumps over 30 lbs., a Severe Series tank must be used. The 30 lb. limit includes pump and any other accessories such as filter kit, meters, etc.

Features

Tank Features

• Multi-Fuel Compatibility: This tank is suitable for a wide range of fuels, including gas, diesel, methanol, kerosene, and aviation fuel.
• Lockable Vent/Prevent Filler Cap: Equipped with a commercial-grade lockable vent/prevent filler cap, providing security.
• Fully Baffled Design: Features a fully baffled interior to reduce the movement of contents during transportation, ensuring stability.
• Reinforced Bungs: Two 2 in. NPT reinforced bungs, providing superior strength and compatibility with various fueling systems.
• Drain Port: Includes a 3/8 in. NPT drain for easy and convenient tank drainage when needed.
• Hold Down Brackets: Designed with hold-down brackets for secure mounting and stability during transport.
• Pressure Leak Detection Test: Prior to shipment, each tank undergoes a pressure leak detection test to ensure it is free from defects.
• Clean and Debris-Free: Our tanks are cleaned both inside and outside, ensuring they are free from debris and contaminants.
• 1-Year Limited Warranty: For added peace of mind, the manufacturer provides a 1-year limited warranty on this fuel transfer tank.
• DOT Certified Special Permit Issued: Our 110 Gallon Split Fuel Transfer Tank comes with a Special Permit issued by the U.S. Department of Transportation (DOT), ensuring its safety and compliance with regulations.

Pump Features

• Versatile Fuel Compatibility: Works with gasoline (up to E15), diesel (up to B20), and kerosene.
• Durable Construction: Lightweight, corrosion-resistant cast aluminum body for long-lasting use.
• Self-Priming: Quick and efficient fuel transfer with no manual priming required.
• Automotive-Friendly: Operates on a 12-Volt DC system, perfect for vehicle-based fuel transfer.
• Automatic Bypass Valve: Protects the pump from damage when the nozzle is closed.
• Motor Protection: Built-in temperature-limiting device for motor safety.
• Precise Control: Manual nozzle for accurate fuel dispensing.
• Optimal Fittings: Standardized fittings for compatibility with various containers and hoses.
• Duty Cycle Management: 15 minutes ON and 30 minutes OFF for optimal performance.
• UL Listed: Meets stringent safety and quality standards for peace of mind.

Specifications

Tank Specifications

• Capacity: 110 Gallons
• Material: Aluminum
• Cap Type: Vent/Prevent Filler Cap
• Bungs: Two 2 in. NPT Reinforced Bungs
• Drain Port: 3/8 in. NPT
• Dimensions: 23 1/2 in. x 48 1/2 in. x 24 in.

Note 1: Mounting tabs extend out 1-1/2 in.
Note 2: Add 2-1/2 in. for cap height

Pump Specifications

• Inlet/Outlet: 3/4 in. NPT
• Mounting: 2 in. NPT
• Flow Rate: 8 GPM (30 LPM)
• Duty Cycle: 15 min. ON, 30 min. OFF
• Operating Pressure: 15 PSI (1.03 bar) - Normal Pressure
• Operating Temperature: -20°F to 125°F (-29°C to 52°C)
• Pump Housing: Corrosion Resistant Diecast Aluminum
• Power Cord: 15 ft. (4.6 m), 14/2 AWG
• Voltage: 12V DC
• Type: Rotary Gear
• Current Draw: 11 Amp
• Motor: 2100 RPM, 1/10 HP, UL Listed to US and Canadian Standards
• Dispensing Hose: 5/8 in. x 10 ft.
• Suction Pipe: 15 to 40 in. (38.1 to 101.6 cm)
• Warranty: 2 Year

Applications: Standard use with Mobile Tanks, Small Tractors & Equipment, Pick-up Trucks, ATVs, Snowmobiles, Racing/Automotive, Electrical/Plumbing Contractors & More

Notes:

• Mounting tabs extend out 1-1/2 in.
• Add 2-1/2 in. for cap height
• Pumps with aluminum threads must be coated with Anti-Seize prior to installation. Do not dry fit. Do not use teflon tape or pipe dope.
• Do not install a pump over 30 lbs. to a standard duty tank. For pumps over 30 lbs., a Severe Series tank must be used.
• This tank must be grounded to your vehicle. Metal to metal contact between mounting hardware and truck bed or running a ground wire to one of the mounting bolts.

* The 30 lb. limit includes pump and any other accessories such as filter kit, meters, etc. Failure to follow these guidelines will result in voiding your warranty. Do not install riser between the fuel tank fitting and the pump.

Contents

• ATTTR110S: 110 gallon split transfer tank 
• GPI13710001: EZ-8 Pump with manual nozzle

Downloads